analysis analytics butane

Accurate Detection Of Residual Solvents In Cannabis Concentrates.

Edibles and vape pens are rapidly becoming a sizable portion of the cannabis industry as various methods of consumption popularize beyond just smoking dried flower. These products are produced using cannabis concentrates, which come in the form of oils, waxes or shatter (figure 1). Once the cannabinoids and terpenes are removed from the plant material using solvents, the solvent is evaporated leaving behind the product. Extraction solvents are difficult to remove in the low percent range so the final product is tested to ensure leftover solvents are at safe levels. While carbon dioxide and butane are most commonly used, consumer concern over other more toxic residual solvents has led to regulation of acceptable limits. For instance, in Colorado the Department of Public Health and Environment (CDPHE) updated the state’s acceptable limits of residual solvents on January 1st, 2017.

Headspace Analysis

Figure 1: Shatter can be melted and dissolved in a high molecular weight solvent for headspace analysis (HS). Photo Courtesy of Cal-Green Solutions.

Since the most suitable solvents are volatile, these compounds are not amenable to HPLC methods and are best suited to gas chromatography (GC) using a thick stationary phase capable of adequate retention and resolution of butanes from other target compounds. Headspace (HS) is the most common analytical technique for efficiently removing the residual solvents from the complex cannabis extract matrix. Concentrates are weighed out into a headspace vial and are dissolved in a high molecular weight solvent such as dimethylformamide (DMF) or 1,3-dimethyl-3-imidazolidinone (DMI). The sealed headspace vial is heated until a stable equilibrium between the gas phase and the liquid phase occurs inside the vial. One milliliter of gas is transferred from the vial to the gas chromatograph for analysis. Another approach is full evaporation technique (FET), which involves a small amount of sample sealed in a headspace vial creating a single-phase gas system. More work is required to validate this technique as a quantitative method.

Gas Chromatographic Detectors

The flame ionization detector (FID) is selective because it only responds to materials that ionize in an air/hydrogen flame, however, this condition covers a broad range of compounds. When an organic compound enters the flame; the large increase in ions produced is measured as a positive signal. Since the response is proportional to the number of carbon atoms introduced into the flame, an FID is considered a quantitative counter of carbon atoms burned. There are a variety of advantages to using this detector such as, ease of use, stability, and the largest linear dynamic range of the commonly available GC detectors. The FID covers a calibration of nearly 5 orders of magnitude. FIDs are inexpensive to purchase and to operate. Maintenance is generally no more complex than changing jets and ensuring proper gas flows to the detector. Because of the stability of this detector internal standards are not required and sensitivity is adequate for meeting the acceptable reporting limits. However, FID is unable to confirm compounds and identification is only based on retention time. Early eluting analytes have a higher probability of interferences from matrix (Figure 2).

Figure 2: Resolution of early eluting compounds by headspace – flame ionization detection (HS-FID). Chromatogram Courtesy of Trace Analytics.

Mass Spectrometry (MS) provides unique spectral information for accurately identifying components eluting from the capillary column. As a compound exits the column it collides with high-energy electrons destabilizing the valence shell electrons of the analyte and it is broken into structurally significant charged fragments. These fragments are separated by their mass-to-charge ratios in the analyzer to produce a spectral pattern unique to the compound. To confirm the identity of the compound the spectral fingerprint is matched to a library of known spectra. Using the spectral patterns the appropriate masses for quantification can be chosen. Compounds with higher molecular weight fragments are easier to detect and identify for instance benzene (m/z 78), toluene (m/z 91) and the xylenes (m/z 106), whereas low mass fragments such as propane (m/z 29), methanol (m/z 31) and butane (m/z 43) are more difficult and may elute with matrix that matches these ions. Several disadvantages of mass spectrometers are the cost of equipment, cost to operate and complexity. In addition, these detectors are less stable and require an internal standard and have a limited dynamic range, which can lead to compound saturation.

Regardless of your method of detection, optimized HS and GC conditions are essential to properly resolve your target analytes and achieve the required detection limits. While MS may differentiate overlapping peaks the chances of interference of low molecular weight fragments necessitates resolution of target analytes chromatographically. FID requires excellent resolution for accurate identification and quantification.

The post Accurate Detection of Residual Solvents in Cannabis Concentrates appeared first on Cannabis Industry Journal.

Aaron Biros

analysis analytics and Bureau for Public Health business cannabis cbd compliance consumer cultivation government growing industry law legal legalization legalize legislation license marijuana market medical medicine METRC Office of Medical Cannabis OMC platform product provider quality regulation regulations Regulatory retail safety sale seed software state system test The West Virginia Department of Health and Human Resources to trace traceability track Virginia West Virginia

Metrc Gets West Virginia Contract

activism analysis analytics ASA awareness brand branding Britain British business Business Analysis camapgin cannabidiol cannabis cbd communications company compliance consumer demographic digital engagement England English expert Federal government great growing industry Kaj Kajal law legal legalization legalize legislation license marijuana market marketing matter medical medicine NICE opportunities PR product Product Development progress public quality reform regulation regulations Regulatory relations retail Shah social media subject UK United Kingdom

The UK Cannabis Industry Needs New PR Strategies

adam jacques analysis analytical chemistry analytics business Business Analysis cannabinoid cannabis cbd Christian West clear CMGL Collaborative Laboratories for Environmental Analysis and Remediation cultivate cultivation Cultivation & Growing Curtis Mathes Grow Lights effects expression flavonoids genetics growing hemp horticultural indoor industry lab laboratories Laboratories & Analytics laboratory labs LC-QTOF-MS LED legalization legalize legislation license light lighting Liquid Chromatography Quadrupole Time-of-Flight Mass Spectrometry manipulation marijuana market Matthew Spurlock phytochemical Phytochrome plant product Product Development Professor Kevin Schug Quality regulations research researcher researching Robert Manes science shimadzu spectrum terpenes test Testing University of Texas at Arlington University of Texas at El Paso UT Zacariah Hildenbrand ZED Therapeutics

UT-Arlington and UT-El Paso to Evaluate Phytochrome Manipulation in Hemp